Pipe and Pipe fitting MCQ Question and Answer | ITI FITTER 2 YEAR

ITI Fitter 2 YEAR Trade Pipe and Pipe fitting MCQ Question and Answer for CBT Online exam for NCVT AITT (All India Trade Test).  Practice all FITTER Trade MCQ (Multiple choice Question). Also you can practice mock test exam online

Fitter 2 year Trade MCQ also useful for competitive exam like PSU Job exam As well as Government Job Exam, Apprentice job.

ITI Fitter 2 year | Pipe and Pipe fitting MCQ

1.

What is the angle of deviations provided on elbows and bends in pipe works?

1. 90° and 45°
2. 30° and 60°
3. 20° and 40°
4. 60° and 45°

2.

How the water flow is stopped from the valve around the stuffing box?

1. Replace the spindle
2. Tightening the bonnet
3. Tightening the hand wheel
4. Packing with asbestos hemp

3.

What is the name of the limit gauge?

1. Vertical position
2. Angular position
3. Radius position
4. Horizontal position

4.

What is the remedial measure to stop the dripping of water from house hold tap even after firmly closed?

1. Replace the tap
2. Replace washer
3. Renew tap spindle
4. Tighten stuffing box

5.

How pipes are classified?

1. Uses
2. Colour
3. Shapes
4. Material

6.

What is the name of the pipe fitting?

1. 45° elbow
2. Tee joint pipe
3. Short radius elbow
4. Long radius elbow

7.

What is the name of the pipe fitting?

1. Tee joint
2. Eccentric reducer
3. Reducer tee joint
4. Concentric reducer

8.

What is the name of the pipe fitting?

1. Coupling
2. Long nipple
3. Eccentric reducer
4. Concentric reducer

9.

Which standard pipe fitting is used to close a pipe line have internal thread?

1. Plug
2. Caps
3. Reducer
4. Coupling

10.

Which type of wrench is used for more than 50 mm dia meter pipe to tight with heavy gripping?

1. Strap wrench
2. Foot print wrench
3. Chain pipe wrench
4. Stilson pipe wrench

11.

What is the name of part marked ‘x’ in the pipe joint?

1. Outer pipe
2. Hemp packing
3. Tapered male thread
4. Parallel female thread

12.

What is the name of the part marked ‘x’?

1. Bonnet
2. Packing
3. Gland nut
4. Shaft or spindle

13.

What is the remedy if the spindle rotates continuously so that the gate valve is not closed?

1. Replace the valve
2. Tighten the gland nut
3. Replace the wornout part
4. Renew the gland packing

14.

Which type of pipe joint take branch at 90°?

1. Coupling
2. Tee branch
3. Ecentric reducer
4. Concentric reducer

15.

What is the name of the plumber tool to assemble or dismantle pipes of 50 mm to 150 mm diameter?

1. Strap wrench
2. Chain pipe wrench
3. Still son pipe wrench
4. Foot point pipe wrench

16.

What is the name of the limit gauge?

1. Socket
2. Plug or cap
3. Union screwed
4. Reducer concentric

17.

What is the type of visual pipe inspection at 30° angle between the plane of vision and surface?

1. Direct visual testing
2. Remote visual testing
3. Translucent visual testing
4. Transparent visual testing

18.

Where concentric reducer used in pipeline?

1. Vertical
2. Horizontal
3. Reduce the pressure
4. Drive the flow direction

19.

What is the name of the part marked ‘X’ in water tap?

1. Handle
2. Bonnet
3. Gland nut
4. Valve seat

20.

Which valve is used to permit fluid flow in one direction only?

1. Plug-cock
2. Needle valve
3. Non-return valve
4. Pressure regulator valve

21.

Which type of wrench is used on finished tubular surface?

1. Strap wrench
2. Foot point wrench
3. Chain pipe wrench
4. Stillson pipe wrench

22.

What is the name of part marked as 'x'?

1. Cutter wheel
2. Adjusting screw
3. Guide rollers
4. Hand lever

23.

What is the capacity of the pipe vice to hold pipes diameter in mm?

1. 68 mm
2. 65 mm
3. 63 mm
4. 72 mm

24.

What is the type of wrench?

1. footprint wrench
2. strap wrench
3. chain pipe wrench
4. pipe wrench

25.

What is the name of the limit gauge?

1. 25 mm
2. 50 mm
3. 30 mm
4. 45 mm

26.

What is the range of external pipe threads cut by pipe dies?

1. ½” to 4”
2. ¼” to 4”
3. 1/8” to 2”
4. ¼” to 6”

27.

What is the part marked as ‘x’ ?

1. Pivot
2. Spring
3. Movable jaw
4. Adjusting nut

28.

Which pipe fitting is used to divert the flow direction of pipe?

1. Union
2. Plug
3. Elbow
4. Coupling

29.

What is the pipe fitting the 90° and the branches may be equal in diameter?

1. Tee joint
2. Elbow joint
3. Coupling joint
4. Union joint

30.

What is the pipe fitting?

1. Reducer
2. Nipple
3. Cap
4. Plug

31.

What is the pipe fitting?

1. Caps
2. Plug
3. Coupling
4. Reducer

32.

Which valve is used to control flow and is only kept in either open or closed position?

1. Gate valve
2. Globe valve
3. Needle valve
4. Non-return valve

33.

Where universal coupling is used?

1. Automobile vehicles
2. Textiles mills
3. Engineering machines
4. Large angle drive

34.

What is the name of the limit gauge?

1. Plate coupling
2. Clamp coupling
3. Slip type coupling
4. Universal coupling

35.

What is the radius size for long radius elbow?

1. Equal the bore the pipe
2. 1 ½ times bore of the pipe
3. 3 time bore of the pipe
4. 2 times bore of the pipe

36.

What is the radius size for the short radius elbow?

1. 1 ½ time bore of the pipe
2. Equal bore of the pipe
3. 3 time bore of the pipe
4. 2 time bore of the pipe

37.

Which is used to divert at 45°in pipeline?

1. Elbow
2. Coupling
3. Reducer
4. Branch

38.

Which standard fitting is used for joining pipeline of different diameter?

1. Plug
2. Caps
3. Reducer
4. Coupling

39.

What type of fitting is used in straight pipeline to connect two pipes of external threads?

1. Reducer
2. Coupling
3. Cap
4. Nibble

40.

what is the cause of water dripping from the tap even after closed?

1. Defective washer
2. Spindle thread wornout
3. Bend spindle
4. Loose valve

41.

What caused loud noise in the tap if turned ON ?

1. Spindle bend
2. Spindle thread wornout
3. Stuffing box packing dry
4. Valve loose on spindle